INSTALLING A BATH TUB

Installing A Bath tub

Installing A Bath tub

Blog Article

Check Us Out

Do you find yourself searching for facts on How to Install a Bathtub Yourself?


How to Install a Bathtub Yourself
Installing a bathtub isn't precisely brain surgery, but it does require solid plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bathtub with a new one is also a moderately tough project. If the old tub is easily obtainable, the task can relocate quickly; if you have to open a wall to eliminate the old tub as well as position the new tub, the job is a lot harder. In either instance, the task is within a home handyman's skills, although you will need a helper to move out the old tub as well as embeded in the new one. Make certain you have qualified on your own for the work and fit trying it. Rather than employing a service provider to take control of a halfway-completed project, it is much better to take into consideration using one before you begin. Opportunities are you might require a professional plumber to make tube connections.
This write-up will certainly help you set up a new tub in your washroom if you have already gotten a brand-new bathtub and don't need to alter the arrangement of your previous water system pipelines.
Your devices as well as product list must make up the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Getting ready for the Setup


    First of all, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps system to avoid stress on the tub.
    Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the provided washing machines.
    Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be fitted in its last position.

    Removing Old Touches


    If you require to replace old faucets with new ones as a part of your installment, then the first thing you should do is separate the supply of water. After doing so, turn on the faucets to drain any kind of water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic because of the restricted gain access to that is frequently the situation.
    Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
    Prior to proceeding to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.

    Setting up the Bath tub


    Using the two wood boards under its feet, place the tub in the needed placement. The wooden boards are practical in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
    The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the bathtub up until the level reviews level.
    To install taps, fit all-time low of the outermost flexible tap port to the proper supply pipeline by making a compression sign up with; then do the same for the other faucet.
    Activate the water and check all joints as well as brand-new pipework for leakages and also tighten them if essential. Fill the bathtub and likewise inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
    Finally, fix the bath paneling as explained in the producer's user's manual. Tiling as well as securing around the bath tub must wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its last position.

    Fitting New Taps


    If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a connection to the existent supply pipelines.
    If you require to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
    Next off, position the tap in the placing opening in the bath/basin making sure that the washers are in area between the tap and also the sink. Safeguard the tap in place with the supplier supplied backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The former kind must be connected to the faucet finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.

    Tiling Around the Tub


    In the location where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack an inflexible seal, causing the water to pass through the wall in between the bath and the tiling, causing complications with moisture and also possible leakages to the ceiling below.
    You can pick from a range of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water before sealing, to permit the movement experienced when the bathtub remains in use. The sealant can fracture relatively early if you do not think about this motion before securing.
    Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water resistant adhesive and also grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    I was guided to that article on Tools You Need to Install a New Bathtub through a friend on our other web property. Are you aware of another individual who is curious about A Step-by-Step Guide to Installing a Bathtub? Take a moment to promote it. Thank you so much for your time spent reading it.




    View Website


    Report this page